SOFTWARE / INFRASTRUCTURE / SECURITY / KENYA
Done
Action completed
Field Notes Wireless Networking & ISP Solutions Cambium Networks Configuration Intermediate • 6 min read

Setting up an Access Point and Subscriber Module

P Author: Peter Mwangi (Senior Network & Field Infrastructure Engineer)
Reviewed by: Lawrence Kamau (Lead Systems Architect & Infrastructure Engineer)
Published: May 1, 2026 • Last Updated: Nov 22, 2026 • Target Hardware: Cambium ePMP 3000 / 3000L Access Points paired with ePMP Force 300 Subscriber Modules (ePMP Firmware v4.6+).

Purpose: Configure an ePMP Access Point (AP) and Subscriber Module (SM) pair so the SM authenticates cleanly, receives its TDD frame schedule, and passes tagged customer VLAN traffic.

Reference Network Topology
Point-to-Multipoint (PtMP) Tower Distribution with Management & Customer VLAN Separation
NODE 01
POP Core Router & Backhaul
MikroTik CCR/RB router fed via licensed/5GHz PtP backhaul
NODE 02
Tower Managed Switch
PoE switch isolating VLAN 99 (Radio Mgmt) from VLAN 120 (Subscriber Traffic)
NODE 03
Sector / Horn Access Point
Cambium ePMP AP or Ubiquiti Rocket Prism 5AC (GPS Sync / TDD)
NODE 04
Multiple Subscriber Modules (SMs)
Cambium Force 300 / Ubiquiti NanoStation & PowerBeam CPEs
NODE 05
Customer Premise Routers
Authenticated via PPPoE / DHCP Option 82 with per-plan rate limits

Prerequisites

  • Access Point and Subscriber Module updated to matching ePMP firmware versions.
  • Defined SSID, WPA2 passphrase, channel width (20 MHz or 40 MHz), and downlink/uplink TDD split ratio (e.g., 75/25).

Step-by-Step Configuration

STEP 01 — Configure the Access Point Radio Parameters

On the AP under Configuration -> Radio, set Mode to Access Point, define a clear sector SSID, select a clean 20 MHz or 40 MHz channel, and set Downlink/Uplink Ratio to 75/25.

STEP 02 — Configure Wireless Security on the AP

Under Configuration -> Security, enable WPA2-AES and configure a strong 16+ character pre-shared key.

STEP 03 — Configure the Subscriber Module (SM) Scan List

On the SM under Configuration -> Radio, set Mode to Subscriber Module, enter the exact AP SSID, and restrict the Scan Frequency List to the AP operating channel to speed up registration.

STEP 04 — Configure SM Data VLAN & Bridge Mode

Under Configuration -> Network, set Network Mode to Bridge and map the customer Ethernet port to the subscriber access VLAN while keeping Management VLAN tagged.

STEP 05 — Verify Registration on Monitor -> Wireless

Confirm the SM appears in the AP Registered Subscribers table with symmetric chain RSSI and active session uptime.

Expected Results & Verification

The Subscriber Module registers to the AP within 15 seconds, displays Registered status under Monitor -> Wireless, and passes customer PPPoE/DHCP traffic transparently.

Troubleshooting Matrix

Issue:
Fix:
Issue:
Fix:
SECURITY HARDENING

Enable AP SM Authentication / RADIUS MAC filtering where supported so unauthorized radios cannot associate to your sector.

BACKUP & RECOVERY

Export both AP and SM configuration templates so replacement SMs can be cloned in minutes during field maintenance.

P
Peter Mwangi Delight Engineering Team
Senior Network & Field Infrastructure Engineer
Specialization: Cambium ePMP, Ubiquiti airMAX, Fiber GPON / SFP+ Distribution & Tower Rigging

Leads physical wireless and optical deployments across Dagoretti South and greater Nairobi, specializing in interference mitigation and high-throughput point-to-point links.

Tested on Delight Living ISP Network (YouBroadband)
Nairobi NOC • Kabiria Road, Dagoretti South
Related Technical Guides
Was this engineering guide helpful?
Need professional installation, auditing, or troubleshooting? Request Network Consultation →