SOFTWARE / INFRASTRUCTURE / SECURITY / KENYA
Done
Action completed
Technical Guide Wireless Networking & ISP Solutions Point-to-Point Wireless Links Intermediate • 6 min read

Establishing a point-to-point wireless connection

M Author: Mercy Wanjiku (Full-Stack Software & Systems Engineer)
Reviewed by: Lawrence Kamau (Lead Systems Architect & Infrastructure Engineer)
Published: May 1, 2026 • Last Updated: Nov 22, 2026 • Target Hardware: Cambium ePMP Force 300-25 (25 dBi dish) and Force 300-19 (19 dBi panel) in ePTP Master / Slave or TDD PtP mode.

Purpose: Build a high-throughput, low-latency Layer-2 wireless backhaul between two towers or office buildings using a dedicated Cambium Force 300 pair.

Reference Network Topology
Point-to-Point Layer-2 Bridge: Main Office -> Cambium/Ubiquiti PtP Radios -> Remote Branch Switch
NODE 01
Main Office Router & Switch
Gateway VLANs (VLAN 10 Mgmt, VLAN 20 Staff, VLAN 30 Voice)
NODE 02
Master Radio (AP PtP / TDD Master)
Cambium Force 300-25 or Ubiquiti PowerBeam 5AC (WDS Transparent Bridge)
NODE 03
5 GHz Outdoor RF Link (Clear Fresnel)
Aligned azimuth/elevation, shielded Cat6 + surge arrestors
NODE 04
Slave Radio (SM PtP / Station)
Remote building rooftop radio (Management IP on VLAN 10)
NODE 05
Remote Distribution Switch & UniFi APs
Trunk port carrying staff & management VLANs to branch desks

Prerequisites

  • Two Force 300 radios with verified line-of-sight and clear Fresnel zone between Site A and Site B.
  • Grounded mounts, shielded outdoor Cat6 cabling, and Ethernet surge protectors at both ends.

Step-by-Step Configuration

STEP 01 — Select ePTP Mode for Dedicated Backhaul

Set Site A to ePTP Master and Site B to ePTP Slave under Configuration -> Radio (or TDD AP/SM if GPS sync with co-located sectors is required).

STEP 02 — Set Channel Bandwidth & Target RSSI

Select 40 MHz (or 20 MHz in noisy urban spectrum) and configure ATPC (Automatic Transmit Power Control) so the remote end receives approximately -52 dBm to -58 dBm.

STEP 03 — Configure Transparent Layer-2 Trunking

Verify Bridge mode is active on both radios so all 802.1Q VLAN tags (Management, Customer PPPoE, Voice) traverse the link unmodified.

STEP 04 — Run Integrated Link Capacity Test

Navigate to Tools -> Link Capacity Test on the Master radio and execute a bidirectional throughput test to confirm modulation reaches MCS8/MCS9 (256-QAM).

Expected Results & Verification

Link locks at 256-QAM (MCS8/9) on both downlink and uplink with chain imbalance under 2 dB and sub-3ms wireless latency.

Troubleshooting Matrix

Issue:
Fix:
Issue:
Fix:
SECURITY HARDENING

Isolate radio management interfaces inside a dedicated Management VLAN inaccessible from customer ports.

BACKUP & RECOVERY

Save configuration backups for both Master and Slave units labeled with site coordinates, azimuth bearing, and channel frequency.

M
Mercy Wanjiku Delight Engineering Team
Full-Stack Software & Systems Engineer
Specialization: PHP 8.3 / Laravel, AI Workflow Triage, Database Optimization & M-Pesa API Architecture

Architects Delight internal platforms, including the YouBroadband billing engine, landlord revenue-sharing portal, and custom CRM ticketing solutions.

Tested on Delight Living ISP Network (YouBroadband)
Nairobi NOC • Kabiria Road, Dagoretti South
Related Technical Guides
Was this engineering guide helpful?
Need professional installation, auditing, or troubleshooting? Request Network Consultation →