SOFTWARE / INFRASTRUCTURE / SECURITY / KENYA
Done
Action completed
Lessons Learned Wireless Networking & ISP Solutions ISP Network Design Intermediate • 7 min read

Setting up a PPPoE server

L Author: Lawrence Kamau (Lead Systems Architect & Infrastructure Engineer)
Reviewed by: Peter Mwangi (Senior Network & Field Infrastructure Engineer)
Published: May 1, 2026 • Last Updated: Nov 22, 2026 • Target Hardware: MikroTik CCR2004, CCR2116, RB5009, and RB4011 running RouterOS v7.x.

Purpose: Deploy a production-grade PPPoE concentrator on a dedicated customer transport VLAN so ISP subscribers authenticate individually, receive dynamic bandwidth queues, and stay isolated from one another.

Reference Network Topology
ISP Core: Upstream Fiber -> MikroTik PPPoE/RADIUS -> Distribution Switch -> Sector APs -> Customer CPE
NODE 01
Upstream Internet Source
Dedicated DIA Fiber / BGP Peering (WAN ether1)
NODE 02
Main Router (MikroTik RouterOS v7)
NAT, Firewall, PPPoE Server + RADIUS, Simple/Queue Trees
NODE 03
Distribution Switch (Managed VLAN Trunk)
VLAN 10 (Mgmt) + VLAN 200 (Customer PPPoE Transport)
NODE 04
Wireless AP / PtP Backhaul
Cambium ePMP Force 300 / Ubiquiti airMAX Sector (VLAN 10 Mgmt)
NODE 05
Subscriber Radio (SM / Station)
Roof-mounted CPE bridged to Customer Router WAN
NODE 06
Customer Router
PPPoE Client dial-up -> Local LAN & Wi-Fi

Prerequisites

  • Dedicated customer transport VLAN (e.g., vlan200-pppoe) bridged to your sector APs and fibre OLTs.
  • Subscriber IP pool (e.g., 10.200.0.0/22) and outbound NAT rules configured for that pool.

Step-by-Step Configuration

STEP 01 — Create Subscriber IP Pool

Under IP -> Pool, create pppoe-pool covering your subscriber range (e.g., 10.200.0.2-10.200.3.254).

STEP 02 — Create PPP Profiles with Rate Limits

Under PPP -> Profiles, create plan profiles (e.g., 20M-Home, 50M-Biz) setting Local Address (10.200.0.1), Remote Address (pppoe-pool), DNS, Only-One=yes, and Rate Limit (rx/tx).

STEP 03 — Bind PPPoE Server to Customer VLAN

Under PPP -> PPPoE Servers, add a server bound strictly to vlan200-pppoe, set Max MTU/MRU to 1480, and check One Session Per Host.

STEP 04 — Configure TCP MSS Clamping

Ensure Change TCP MSS is enabled on the PPP profile so websites load cleanly over the 1480-byte PPPoE MTU without fragmentation.

CLI / Configuration Snippet

# RouterOS v7.x — PPPoE Concentrator on Customer VLAN 200
/ip pool add name=pppoe-pool ranges=10.200.0.2-10.200.3.254

/ppp profile add name="PLAN-30M" local-address=10.200.0.1 remote-address=pppoe-pool \
  dns-server=1.1.1.1,8.8.8.8 rate-limit="30M/30M" only-one=yes change-tcp-mss=yes

/interface pppoe-server server add service-name="delight-isp" interface=vlan200-pppoe \
  default-profile="PLAN-30M" max-mtu=1480 max-mru=1480 one-session-per-host=yes disabled=no
Expected Results & Verification

Active PPPoE sessions appear dynamically under Interfaces (as <pppoe-username> bindings) with automatic dynamic Simple Queues enforcing plan speeds.

Troubleshooting Matrix

Issue:
Fix:
SECURITY HARDENING

Disable PAP authentication (allow MS-CHAPv2 / CHAP) and isolate subscriber traffic from Management VLANs via forward-chain firewall rules.

BACKUP & RECOVERY

Back up PPP secrets and profiles nightly—or centralise subscriber auth via FreeRADIUS / Delight ISP Suite.

L
Lawrence Kamau Delight Engineering Team
Lead Systems Architect & Infrastructure Engineer
Specialization: MikroTik RouterOS 7, FreeRADIUS, Linux CWP Hosting Clusters & Network Architecture

Directs network architecture and server infrastructure at Delight Office Solutions, overseeing the core YouBroadband ISP routing matrix and enterprise deployments.

Tested on Delight Living ISP Network (YouBroadband)
Nairobi NOC • Kabiria Road, Dagoretti South
Related Technical Guides
Was this engineering guide helpful?
Need professional installation, auditing, or troubleshooting? Request Network Consultation →